
The display DDU 9 integrates a programmable full color dashboard display with a data logging system for motorsport applications for a very competitive price. Additional input devices can be connected via Ethernet and CAN buses.
Data Analysis Software WinDarab is available free of charge as “WinDarab V7 free” on our website. A basic logging function of 100 channels with recording of 50 ms (3 GB) is always included. The logger can be upgraded to full logging performance (max. 1 ms). In addition a 2nd logging partition of 1 GB (e.g. for long term recording) can be activated.
Customers can implement own graphics, pictures etc. on the 12 freely configurable display pages. For quick data transfer from the car e.g. during pit stop, data copy to a USB stick is available as an option. The stick is connected to the wiring harness for the DDU 9.
The device comes with 4 analogue and 4 speed inputs as standard; further 12 analogue inputs are available as optional upgrade.
- Features
- Application
- Technical Specifications
- Communication
- Installation Notes
- Ordering Information
- Downloads
Features
- Cutting-edge 667 MHz Dual Core Processor
- Large trans-reflective color display
- Recording on USB flash drive (opt.)
- Supports GPS laptrigger, pre-dated lap time etc.
- Page change based on events possible
Application
Display |
| |
Resolution | 640 x 480 pixel | |
Supported image file formats | BMP, GIF, JPG, PNG, TIF | |
Processor | 667 MHz Dual Core | |
Converters | 8 kHz AD converters with digital low pass filter | |
Internal power source | Li/Ion capacitor | |
Configurable math channels |
| |
User configurable CAN in/out messages | ||
Sampling rate | 50 ms (standard), | |
Online data compression |
| |
Logging rate | Max. 600 kB/s | |
Recording channels | 100 channels (standard), | |
Logged data download speed | Max. 1,000 kB/s | |
Internal storage capacity | 3 GB (standard), | |
LTE Ethernet telemetry support, GSM telemetry support | ||
RS232 for GPS and telemetry |
| |
CCP-Master, data acquisition from ECU that support CAN calibration protocol (optional) |
Technical Specifications
Mechanical Data
Size | 151 x 126 x 33.5 mm |
Weight | 540 g |
Protection Classification | IP54 to DIN 40050, Section 9, Issue 2008 |
Operating temperature internal | -20 to 85°C |
Operating temperature Display | -20 to 70°C |
Max. vibration | Vibration profile 1 (see Appendix or www.bosch-motorsport.com) |
Electrical Data
Supply voltage | 5 to 18 V |
Inputs
Analog channels | 4 standard, additional 12 optional |
Input range | 0 to 5 V |
Resolution | 12 bit |
Switchable pull up resistor | For all ANA_IN |
Wheel speed inputs | 4 Hall-effect or DF11, switchable |
Outputs
Sensor supply 5 V ± 1 % (250 mA) | 2 |
Sensor supply 10 V ± 1 % (250 mA) | 1 |
Sensor supply U_Bat 250 mA | 1 |
Sensor ground | 4 |
Environment
External switch for page selection, 12 steps | B 261 209 658-01 |
External switch for brightness adjustment or page selection, 6 steps | B 261 209 659-01 |
Optional Upgrades | |
USB Kit | Rugged USB flash drive Bosch File System (BFS) format, works with Bosch File System (BFS) preformatted USB Flash drive only Adapter cable to USB-Port Adapter for wiring harness SW licence USB-Port unlocked |
CCP_MASTER | CCP-Master (ASAP2 file from ECU manufacturer required) |
FULL_LOG_1 | Enable full logging performance of 3 GB partition 1 |
FULL_LOG_2 | Enable full logging performance of 1 GB partition 2 |
I_O EXTENS | Enable additional 12 analog input channels |
Connectors and Wires
Motorsport connector on Display | AS216-35PN |
Mating connector | F 02U 000 466-01 |
Pin Configuration
Pin | Name | Comment | Status |
---|---|---|---|
1 | KL_31 |
| Incl. |
2 | KL_15 |
| Incl. |
3 | KL_30 |
| Incl. |
4 | Rev_In_3 | Hall or DF11 switchable | Incl. |
5 | Rev_In_1 | Hall or DF11 switchable | Incl. |
6 | KL_31 |
| Incl. |
7 | CAN_2_L | CAN speed selectable | Incl. |
8 | Ethernet_2_TXP |
| Incl. |
9 | Ethernet_2_TXN |
| Incl. |
10 | Sens_Power_12V | over current protected | Incl. |
11 | Rev_In_4 | Hall or DF11 switchable | Incl. |
12 | Rev_In_2 | Hall or DF11 switchable | Incl. |
13 | Laptrigger_In |
| Incl. |
14 | CAN_2_H | CAN speed selectable | Incl. |
15 | CAN_1_H | CAN speed selectable | Incl. |
16 | Ethernet_2_RXP |
| Incl. |
17 | Sens_Gnd_4 | fused | Incl. |
18 | Sens_Power 5V | over current protected | Incl. |
19 | ANA_IN_3 | 3.01 kOhm switchable | Incl. |
20 | ANA_IN_4 | 3.01 kOhm switchable | Incl. |
21 | Time_Sync | connection to Bosch ECU | Incl. |
22 | CAN_1_L | CAN speed selectable | Incl. |
23 | Ethernet_screen |
| Incl. |
24 | Ethernet_2_RXN |
| Incl. |
25 | Sens_Gnd_3 | fused | Incl. |
26 | Sens_Power 5V | over current protected | Incl. |
27 | ANA_IN_7 | 3.01 kOhm switchable | Opt. |
28 | ANA_IN_1 | 3.01 kOhm switchable | Incl. |
29 | USB_Device_DP | to Bosch USB stick | Opt. |
30 | RS232_TX_Telemetry |
| Incl. |
31 | Ethernet_1_TXP |
| Incl. |
32 | Sens_Gnd_2 | fused | Incl. |
33 | Sens_Power_10V | over current protected | Incl. |
34 | ANA_IN_8 | 3.01 kOhm switchable | Opt. |
35 | ANA_IN_10 | 3.01 kOhm switchable | Opt. |
36 | USB_Device_Gnd | to Bosch USB stick | Opt. |
37 | USB_Device_DN | to Bosch USB stick | Opt. |
38 | RS232_RX_Telemetry | e.g. GSM telemetry | Incl. |
39 | Ethernet_1_TXN |
| Incl. |
40 | Sens_Gnd_1 | fused | Incl. |
41 | ANA_IN_11 | 3.01 kOhm switchable | Opt. |
42 | ANA_IN_9 | 3.01 kOhm switchable | Opt. |
43 | RS232_TX_GPS |
| Incl. |
44 | ANA_IN_16 | 3.01 kOhm switchable | Opt. |
45 | USB_Device_Power | to Bosch USB stick | Opt. |
46 | Ethernet_1_RXP |
| Incl. |
47 | ANA_IN_12 | 3.01 kOhm switchable | Opt. |
48 | ANA_IN_6 | 3.01 kOhm switchable | Opt. |
49 | ANA_IN_2 | 3.01 kOhm switchable | Incl. |
50 | ANA_IN_13 | 3.01 kOhm switchable | Opt. |
51 | ANA_IN_15 | 3.01 kOhm switchable | Opt. |
52 | Ethernet_1_RXN |
| Incl. |
53 | ANA_IN_5 | 3.01 kOhm switchable | Opt. |
54 | RS232_RX_GPS | for GPS sensor input | Incl. |
55 | ANA_IN_14 | 3.01 kOhm switchable | Opt. |
Communication
Installation Notes
Inspection services recommended after 220 h or 2 years, no components to replace. |
Ordering Information
Display DDU 9
Order number: F 02U V02 300-02
Accessories
Vehicle Loom Basic
Order number: F 02U V02 735-01
Bench Loom
Order number: F 02U V02 349-01
USB Kit for C 70, DDU 9, DDU 10 and VCU
Order number: F 02U V02 214-01
Software Options
CCP_MASTER
Order number: F 02U V02 213-01
FULL_LOG_1
Order number: F 02U V02 304-01
FULL_LOG_2
Order number: F 02U V02 305-01
I_O EXTENS
Order number: F 02U V02 205-01