Data Logger C 60

The data logger C 60 is a compact and light weight data logging system for motorsport applications. This allows for synchronized acquisition of engine data from the ECU and chassis data from up to 26 analog and 4 digital input channels. Additional input devices can be connected via Ethernet and CAN buses.

Recorded data from the 2 GB logger can be downloaded via high speed Ethernet or via wireless connection with the BT 60 burst telemetry system.

Software upgrades for the C 60 (field upgradable by entering a key) activate additional recording on USB flash drive, CCP-master and additional input channels.

Features

  • Compact and light weight data logger
  • Aluminum housing
  • Recording on USB flash drive (opt.)
  • Two motorsport connectors

Application

Converters

8 kHz AD converters with digital low pass filter

Configurable math channels

User configurable CAN in/out messages

Sampling rate

Max. 1,000 Hz for all channels

Online data compression

 

Logging rate

Max. 300 kB/s

Recording channels

Up to 720 per connected device

Logged data download speed

Max. 1,000 kB/s

Internal storage capacity

2 GB

3-port network switch

 

BT 60 WLAN burst telemetry support

FM 40 long range telemetry support, GSM telemetry support

RS232 GPS input

 

CCP-Master, data acquisition from ECU that support CAN calibration protocol (optional)

Technical Specifications

Mechanical Data

Size

105 x 34.5 x 137.5 mm

Weight

495 g

Protection Classification

IP67 to DIN 40050, Section 9, Issue 2008

Operating temperature (internal)

-20 to 65°C

Max. vibration

Vibration profile 1 (see Appendix or www.bosch-motorsport.com)

Electrical Data

Supply voltage

8 to 18 V

Max. power consumption (w/o loads)

10 W at 14 V

Inputs

Analog channels

6

Input range

0 to 5 V

Resolution

12 bit

Switchable pull up resistor

3 kOhm

Outputs

PWM outputs (low side switch 2 A each)

4

Sensor supply 5 V ± 1 % (250 mA)

1

Environment

Software Upgrade 1

GPS input

 

Additional analog channels

20

Rotational channels (input Hall/inductive)

4

Additional sensor supply 5 V (250 mA each)

3

Sensor supply 10 V (250 mA)

1

Sensor supply 12 V (1 A), non regulated

1

RS232

GPS

 

F 02U V00 703-01

Software Upgrade 2

CCP-Master (ASAP 2 file from ECU manufacturer required)

F 02U V00 797-01

Software Upgrade 3

USB-Port unlocked (Rugged USB flash drive 2 GB Bosch File System (BFS) format included, works with Bosch File System (BFS) preformatted USB flash drive only)

F 02U V00 872-02

Adapter cable to USB-Port (included in Upgrade)

F 02U V01 343-01

Adapter for wiring harness (included in Upgrade)

F 02U 002 996-01

Connectors and Wires

Motorsport connectors double density

2 x 41 pins

Mating connector I
AS-DD 6-12-41SN

F 02U 002 216-01

Mating connector II
AS-DD 6-12-41SA

F 02U 004 180-01

Pin Layout

ASDD-2-12-41PN

Pin

Name

Description

1

KL30

 

2

KL15

 

3

KL15

 

4

KL31

 

5

KL31

 

6

Ethernet Channel0 Tx plus

Wire Ethernet_0 - TX+

7

Ethernet Channel0 Tx minus

Wire Ethernet_0 - TX-

8

Ethernet Channel0 Rx plus

Wire Ethernet_0 - RX+

9

Ethernet Channel0 Rx minus

Wire Ethernet_0 - RX-

10

Ethernet Schirm

Ethernet Schirm

11

Ethernet Channel1 Tx plus

Wire Ethernet_0 - TX+

12

Ethernet Channel1 Tx minus

Wire Ethernet_0 - TX-

13

Ethernet Channel1 Rx plus

Wire Ethernet_0 - RX+

14

Ethernet Channel1 Rx minus

Wire Ethernet_0 - RX-

15

Ethernet Channel2 Tx plus

Wire Ethernet_0 - TX+

16

Ethernet Channel2 Tx minus

Wire Ethernet_0 - TX-

17

Ethernet Channel2 Rx plus

Wire Ethernet_0 - RX+

18

Ethernet Channel2 Rx minus

Wire Ethernet_0 - RX-

19

CAN_A_H

CAN_A - HIGH

20

CAN_A_L

CAN_A - LOW

21

CAN_B_H

CAN_B - HIGH

22

CAN_B_L

CAN_B - LOW

23

USB Power

500mA USB_Power

24

USB Data Plus

USB_OTG_Plus

25

USB Data Minus

USB_OTG_Minus

26

USB GND

USB_Ground

27

SENSPWR5_1

 

28

SENSGND

 

29

Timestamp

 

30

LS_GND_1

Low-Side Ground2

31

LS_SWITCH_1

lowside switch 2A

32

LS_SWITCH_2

lowside switch 2A

33

LS_SWITCH_3

lowside switch 2A

34

LS_SWITCH_4

lowside switch 2A

35

LS_GND_2

Low-Side Ground2

36

ANAIN_M1_1

0 to 5V Analog

37

ANAIN_M1_2

0 to 5V Analog

38

ANAIN_M1_3

0 to 5V Analog

39

ANAIN_M1_4

0 to 5V Analog

40

ANAIN_M1_5

0 to 5V Analog

41

ANAIN_M1_6

0 to 5V Analog

ASDD-2-12-41PA

Pin

Name

Description

1

UBATT_FUSE1

 

2

SENSPWR10_1

 

3

SENSPWR5_2

 

4

SENSPWR5_3

 

5

SENSPWR5_4

 

6

SENSGND

 

7

SENSGND

 

8

RS232A TX

RS232A - Transmit

9

RS232A RX

RS232A - Receive

10

RS232B TX

RS232A - Transmit

11

RS232B RX

RS232A - Receive

12

RS232_GND

RS232_GND

13

REV1_P

DHE I/P or Inductive - KW+

14

REV1_M

DHE I/P or Inductive - KW-

15

REV2_P

DHE I/P or Inductive - KW+

16

REV2_M

DHE I/P or Inductive - KW-

17

REV3_P

DHE I/P or Inductive - KW+

18

REV3_M

DHE I/P or Inductive - KW-

19

REV4_P

DHE I/P or Inductive - KW+

20

REV4_M

DHE I/P or Inductive - KW-

21

ANAIN_M1_7

0 to 5V Analog

22

ANAIN_M1_8

0 to 5V Analog

23

ANAIN_M1_9

0 to 5V Analog

24

ANAIN_M1_10

0 to 5V Analog

25

ANAIN_M1_11

0 to 5V Analog

26

ANAIN_M1_12

0 to 5V Analog

27

ANAIN_M1_13

0 to 5V Analog

28

ANAIN_M1_14

0 to 5V Analog

29

ANAIN_M1_15

0 to 5V Analog

30

ANAIN_M1_16

0 to 5V Analog

31

ANAIN_M2_1

0 to 5V Analog

32

ANAIN_M2_2

0 to 5V Analog

33

ANAIN_M2_3

0 to 5V Analog

34

ANAIN_M2_4

0 to 5V Analog

35

ANAIN_M2_5

0 to 5V Analog

36

ANAIN_M2_6

0 to 5V Analog

37

ANAIN_M2_7

0 to 5V Analog

38

ANAIN_M2_8

0 to 5V Analog

39

ANAIN_M2_9

0 to 5V Analog

40

ANAIN_M2_10

0 to 5V Analog

41

LAPTRIGGER

 

Communication

Configuration via RaceCon over Ethernet or MSA-Box II

CAN interfaces

2

Ethernet 100BaseT

3

RS232

Telemetry

Lap trigger input

1

Installation Notes

Inspection services

Recommended after 100 h

Depending on your experience calibrating Bosch ECUs, we recommend calibration support from Bosch Motorsport.

Please remember that the mating connectors and the programming interface MSA Box II are not included and must be ordered separately.

Not reverse polarity protected on supply or outputs.

Software

The required software (.pst file) for this device is available in the download area of our homepage www.bosch-motorsport.com.

Download data and save configurations before sending device as it will be reset during service.

Accumulator Service

Internal accumulator for data preservation and clock included

Recommended service interval: 24 months (inclusive accumulator change)

Send device to Bosch dealer for service.

Charge accumulator for > 6 h after installation (supply with power).

Charge accumulator twice per year for > 6 h (supply with power).

Ordering Information

Data Logger C 60

Order number: F 02U V00 875-03

Software Options

SW Upgrade 1

Order number: F 02U V00 703-01

SW Upgrade 2

Order number: F 02U V00 797-01

SW Upgrade 3

Order number: F 02U V00 872-02

Downloads